Drainage Shower Channel

Drop Protection Cuff Drop Protection Cuff

In many bathrooms, pipes lead through the wall and the tiles to the tap. To avoid moisture damage, the pipe penetrations must be sealed. Specially designed for wall-mounted taps (hot/cold), our drop protection cuff ensures that everything stays watertight.

Changing from hot to cold and vice versa keeps the pipe system in the wall in constant motion. With many competing products, material fatigue occurs over the years. This can cause tiny leaks through which moisture can penetrate the substrate, damaging the fabric of the building. With our especially durable cuff, this will not happen to you.

If a pipe leading through the wall is exposed during restoration, subsequent sealing may be necessary, depending on the installation situation. Thanks to its simple installation, our drop protection cuff is also ideally suited for this purpose.

Request a hy efficiency kit

  • Drop Protection Cuff

Pyramid Pyramid

The pyramid allows you to kill several birds with one stone. You can use it to seal all three sides of inside corners simultaneously. With just one element, you can create secure wall/wall and wall/floor connections that are guaranteed to prevent the penetration of water.

The installation could not be easier. First, you insert the pyramid into the corner and then you extend it at all three points with corner tape. The overlapping adhesion ensures perfect watertightness.

If necessary, you can shorten the pyramid individually and thereby optimally adapt it to your installation situation. You just have to make sure that there is enough space left for a sufficiently large overlap.

Request a hy efficiency kit

  • Pyramid

Shower Channel Sealing Strip Shower Channel Sealing Strip

The sealing strip for shower channels essentially does the same thing as the tub sealing tape, but for line and point drains. It ensures the permanently watertight sealing of shower channels in the floor area. To fit it, simply glue all around the flange and cut out the inner body.

Thanks to its high elasticity, the shower channel sealing strip adapts to the movements of the shower channel caused by changes in temperature. Unlike competing products, there is no fear of material fatigue, even after years of use. The cuff remains watertight, permanently fulfilling its intended purpose. It can be universally used for all types and surfaces.

Request a hy efficiency kit

  • Shower Channel Sealing Strip

Corner Tape Corner Tape

The corner tape is used in conjunction with sealing membranes to create waterproof wall/wall and wall/floor transitions. You need it, for example, to seal shower channels to the wall and the floor or to protect the corner area from above from penetrating moisture. For installation purposes, you can easily fold it at a 90° angle. 45° are also possible.

The corner adhesive tape serves as a connecting link and supplement to the sealing membranes. To ensure absolute watertightness, you must work with overlaps. As the tape is 100 mm wide and 100% fleece-free, it offers you enough space on both sides to apply the membranes. Thanks to its elasticity, the corner tape can be fixed without tension. This ensures maximum adhesion.

Request a hy efficiency kit

  • Corner Tape

Base Sealing Tape Base Sealing Tape

When showering and bathing, steam can form, which condenses into water on the walls. From there it continues to flow towards the ground and can penetrate it if the sealing is insufficient. As required by DIN 18534, we recommend that watertight wall/floor transitions be installed in areas exposed to spray and drain water. Our base tape is best suited for this purpose.

Unlike the similar-looking corner sealing tape, the front of the base sealing tape is half-covered with fleece. This ensures the good adhesion of subsequently applied wall coverings. The base tape is fitted in the same way as the corner tape. You just have to make sure that you place the fleece-covered area on the wall and the fleece-free area on the floor.

Request a hy efficiency kit

  • Base Sealing Tape

Sealing Membrane Sealing Membrane

Our self-adhesive sealing membrane, which acts like a sealant, is an efficient alternative to liquid sealants based on dispersion, cement or synthetic resin, as well as to film sheeting. Unlike these materials, it achieves an adhesive strength of at least 20 tons per square metre within seconds. This makes time-consuming drying times a thing of the past.

The adhesive adapts perfectly to walls and floors. It adheres to drywall, wooden substructures, walls bound with lightweight plaster, as well as all substrates standardised according to DIN 18534. The 0.5 mm thick foam layer compensates for small irregularities and ensures that the sealing membrane fits perfectly.

The 50 mm wide adhesive edge/overlap ensures capillary protection and complies fully with the current standard. This capillary protection zone with its high elasticity has even been patented. Prefabricated for gluing on additional membranes, the sealing membrane is highly variable in its potential use. Thanks to its resistance to chemicals and alkalis, it is extremely durable. Directly after gluing, you can apply any type of wall covering, for example tiles.

While conventional sealing membranes have a width of one metre, our self-adhesive version is only 500 mm wide. This corresponds to an average arm length. This makes handling easier and prevents installation errors. Such errors would be particularly annoying, as it is not possible to move the sealing membranes afterwards. With us: fixed means fixed.

Since the membranes are suitable for overlapping gluing, there is no residue or waste when shortening. With fleece-free sealing membranes, you can also continue to use short pieces without difficulty. This makes the sealing membrane extremely sustainable and cost-efficient. For a perfect finish at the edges, there is a 100 mm wide finishing strip that you simply stick onto the fleece-free zone.

Request a hy efficiency kit

  • Sealing Membrane

Drain inside corner

Contact us

Contact: Hyon